Written by Acorn Sales Company, manufacturing stamps and seals since 1964 · Reviewed by Holly R, VP of Sales and Marketing at Acorn Sales, against the New Mexico Board of Licensure for Professional Engineers and Professional Surveyors and 16.39.3.12 NMAC on 21 September 2026 · Updated 21 September 2026
New Mexico dictates the artwork, not just the wording. Under 16.39.3.12(C)(1) NMAC the standard seal is three concentric circles, the outermost one and one-half inches in diameter, the middle one inch, the innermost one-half inch, and the rule then assigns content ring by ring: “The outer ring shall contain the words, ‘professional engineer’ and the licensee’s name. The inner ring shall contain the words ‘New Mexico’. The center circle shall contain the license number issued by the board.” A manufacturer border pattern is accepted. A device that carries all four elements but arranges them differently is not the standard design.
That matters because of a figure that travels around as though it were a general New Mexico rule. The 0.1 inch minimum text height applies only to the board-approved alternative design under 16.39.3.12(C)(1)(2), which is the route for any layout other than the three circles and is legal only once the board approves it. The standard three-circle design has no stated minimum text height at all. Quoting 0.1 inches on a three-circle order is quoting the wrong paragraph.
Three device types are lawful: impression type, rubber type, or a computer-generated facsimile that is a bona fide copy of the actual seal specific to the work being presented. But the signature beside it may not be a stamp. 16.39.3.12(A) NMAC requires the original signature of the licensee adjacent to the seal along with the date the signature was applied, and adds: “Rubber stamps signatures are not acceptable.” A combined signature-and-seal die is a product the rule forbids.
New Mexico PE seal requirements at a glance
| Requirement | New Mexico rule | Source |
|---|---|---|
| Seal required | Yes | 16.39.3.12 NMAC |
| Required elements | The words “professional engineer”, Your name as licensed, The words “New Mexico” and Your license number issued by the board | 16.39.3.12(C) NMAC |
| Size and shape | Outermost circle one and one-half inches in diameter, middle circle one inch, innermost circle one-half inch. | 16.39.3.12(C)(1) and (C)(1)(2) NMAC |
| Device allowed | Three device types are named: “The seal/stamp shall be the impression type seal, the rubber type, or a computer-generated facsimile. | 16.39.3.12(B) NMAC |
| Signature and date | Both signature and date are required, adjacent to the seal, and one common shortcut is banned outright: “Adjacent to the seal/stamp shall appear the original signature of the licensee along with the date the signature was applied. | 16.39.3.12(A) NMAC |
| What must be sealed | Final engineering design drawings, the certification page of specifications, and engineering reports prepared by the licensee in responsible charge (subsection A). | 16.39.3.12(A), (E), (F) and (G) NMAC |
| Electronic seal | Electronic signatures are permitted as an option, with the security burden on the licensee: “An electronic signature, as an option to a permanently legible signature, is acceptable for professional documents. | 16.39.3.12(H) and (A) NMAC |
| Renewal and lapse | Not addressed. | 16.39.3.12(D) NMAC (grandfathered seals) |
| Firm number on documents | No firm license and no firm number on the document, which is the opposite of most neighboring states. | NMSA 1978 § 61-23-21 |
| Licensing board | The New Mexico Board of Licensure for Professional Engineers and Professional Surveyors | 16.39.3 NMAC, Engineering Licensure, Disciplines, Applications, Exams, Practice, Seal of Licensee |
Rules for other states are on PE stamp requirements by state.
Is a seal required in New Mexico?
New Mexico requires a seal The duty sits in both places and the board rule is the operative one. NMSA 1978 § 61-23-19 requires that “All plans, designs, drawings, specifications or reports that are involved in such practice, or that are issued by or for the practice, shall bear the seal and signature of the professional engineer in responsible charge of and directly responsible for the work issued.” The rule fixes the trigger document by document: 16.39.3.12(A) NMAC requires a seal that “shall appear on all final engineering design drawings, the certification page of all specifications and engineering reports prepared by the licensee in responsible charge.”.
What must appear on the seal
- The words “professional engineer”
- Your name as licensed
- The words “New Mexico”
- Your license number issued by the board
New Mexico prescribes geometry, not just words. Under 16.39.3.12(C)(1) the standard design is three concentric circles: “The outer ring shall contain the words, ‘professional engineer’ and the licensee’s name. The inner ring shall contain the words ‘New Mexico’. The center circle shall contain the license number issued by the board.” Manufacturer border patterns are accepted. The alternative at (C)(1)(2) is a board-approved design carrying the same four elements with text no less than 0.1 inches high. Subsection (D) grandfathers older devices: engineers licensed before the current rules who have kept continuous licensure may keep a previously approved seal. Nothing is expressly prohibited on the face, but a device that mixes the four elements into a single ring is not the standard design and needs board approval.
Size and shape
Outermost circle one and one-half inches in diameter, middle circle one inch, innermost circle one-half inch. The rule’s words: “the outermost circle being one and one-half inches in diameter, the middle circle being one inch in diameter, and the innermost circle being one-half inch in diameter.” There is no stated minimum text height for that standard design. The 0.1 inch minimum text height applies only to the alternative board-approved design under (C)(1)(2), and conflating the two is a common error.
Embosser, rubber stamp or digital
Three device types are named: “The seal/stamp shall be the impression type seal, the rubber type, or a computer-generated facsimile. Computer generated seals shall be bona fide copies of the actual seal/stamp specific to the work being presented.” The safe buy is a rubber or self-inking stamp cut to the three-circle geometry, because an impression-type embosser does not reproduce on scanned permit sets and a computer-generated facsimile is only lawful if it is a true copy of an actual device the licensee holds.
Signing and dating
Both signature and date are required, adjacent to the seal, and one common shortcut is banned outright: “Adjacent to the seal/stamp shall appear the original signature of the licensee along with the date the signature was applied. Rubber stamps signatures are not acceptable. Electronic signatures as provided by law and board’s policy shall be acceptable.” The date is the date the signature was applied, not the date of the seal or of the drawing. Nothing requires the signature to cross the seal.
New Mexico is one of the few states that dictates the ring geometry, not just the wording
Most boards say what words must appear and leave the artwork alone. New Mexico specifies three concentric circles at one and one-half, one and one-half inch diameters, and then assigns content ring by ring: “professional engineer” and the licensee’s name in the outer ring, “New Mexico” in the inner ring, the license number in the center circle. A stamp that carries all four elements but arranges them differently is not the standard design; it is the alternative design under 16.39.3.12(C)(1)(2), which is legal only if the board approves it and the text is at least 0.1 inches high.
Which documents must be sealed
Final engineering design drawings, the certification page of specifications, and engineering reports prepared by the licensee in responsible charge (subsection A). Subsection E permits a licensee in responsible charge to sign, seal and date documents the licensee did not personally prepare where another licensed engineer sealed them and the licensee or supervised persons reviewed and tested the work. Subsection F limits seal and signature to work in the licensee’s responsible charge and within the licensee’s discipline. Subsection G governs sets: the first or title page carries the responsible licensee’s seal and signature, each sheet is sealed and signed by the licensee or licensees responsible for it, and where several licensees sign, each person’s portion of the work must be identified. The Board publishes an Industrial Exemption FAQ (approved April 12, 2024) for exempt in-house work; that document was not read.
Electronic and digital seals
Electronic signatures are permitted as an option, with the security burden on the licensee: “An electronic signature, as an option to a permanently legible signature, is acceptable for professional documents. The licensee shall provide adequate security regarding the use of the seal and signature. If the document contains more than one licensee and is electronically transmitted as specified under the preceding paragraph, each signature must contain an independent electronic signature.” No certificate authority, cryptographic standard or file format is named. Subsection A conditions acceptance on “law and board’s policy,” so a board policy statement can change practice without a rule amendment.
Renewal, lapse and retirement
Not addressed. Neither 16.39.3 NMAC nor the Engineering and Surveying Practice Act says what becomes of the seal on expiration, lapse, retired or inactive status, or revocation, and neither says whether the license number changes on reinstatement. Checked 16.39.3.11 and 16.39.3.12 NMAC and the 2025 Practice Act. What the rule does provide is a one-way grandfather clause: subsection D lets engineers licensed under earlier rules who maintained continuous licensure keep a previously approved seal, which implies that a break in licensure ends that protection.
Firm registration
No firm license and no firm number on the document, which is the opposite of most neighboring states. NMSA 1978 § 61-23-21(A) states that “No business entity shall be licensed pursuant to the Engineering and Surveying Practice Act.” Instead the entity files an affidavit: 16.39.3.11(E) NMAC requires that “an authorized company officer and the professional engineer who is employed by the business entity and in responsible charge shall place on file with the board within 30 days a signed affidavit, as prescribed by board rule,” kept current and revised within 30 days of any change. Nothing requires a firm number, affidavit number or certificate of authorization number on a sealed document.
What to check before you order
The standard design is three circles: 1-1/2″ outer, 1″ middle, 1/2″ inner. The outer ring carries “professional engineer” plus your name, the inner ring carries “New Mexico,” and the center carries your board-issued license number; a manufacturer border pattern is acceptable. Impression type, rubber type and computer-generated facsimile are all lawful, but a computer-generated seal must be a bona fide copy of an actual device. Signature stamps are prohibited, so never order a rubber signature die, and leave clear space adjacent to the seal for an original signature and the date it was applied. Any layout other than the three-circle design requires you to obtain board approval first, which makes it a custom item.
Browse professional engineer stamps and seals.
- Understanding and Using New Mexico Engineering Stamps and Seals
- Where to Buy Engineer Stamp in New Mexico Today
Frequently asked questions
Do I need a PE seal in New Mexico?
Yes. NMSA 1978 § 61-23-19 requires that “All plans, designs, drawings, specifications or reports that are involved in such practice, or that are issued by or for the practice, shall bear the seal and signature of the professional engineer in responsible charge of and directly responsible for the work issued.” The board rule is the operative one document by document: 16.39.3.12(A) NMAC requires the seal on all final engineering design drawings, the certification page of all specifications, and engineering reports prepared by the licensee in responsible charge.
What size is a New Mexico PE seal?
Three concentric circles at one and one-half inches, one inch and one-half inch in diameter. The rule’s own words: “the outermost circle being one and one-half inches in diameter, the middle circle being one inch in diameter, and the innermost circle being one-half inch in diameter.”
Is there a minimum text height on a New Mexico seal?
Only on the alternative design. The 0.1 inch minimum attaches to the board-approved alternative under 16.39.3.12(C)(1)(2) NMAC, which carries the same four elements in a different arrangement. There is no stated minimum text height for the standard three-circle design, and conflating the two is a common error.
What goes in each ring of a New Mexico seal?
Outer ring: the words professional engineer and your name as licensed. Inner ring: the words New Mexico. Center circle: the license number issued by the board. Those four elements are set out in 16.39.3.12(C) NMAC, and the ring assignment is in (C)(1). A manufacturer border pattern is accepted. Nothing is expressly prohibited on the face, but mixing the four elements into a single ring makes the device an alternative design needing board approval.
Can I use a rubber stamp, an embosser or a computer-generated seal?
All three. 16.39.3.12(B) NMAC: “The seal/stamp shall be the impression type seal, the rubber type, or a computer-generated facsimile. Computer generated seals shall be bona fide copies of the actual seal/stamp specific to the work being presented.” A rubber or self-inking stamp cut to the three-circle geometry is the practical choice, since an impression-type embosser does not reproduce on scanned permit sets and a computer-generated facsimile is lawful only as a true copy of a device the licensee holds.
Can I use a signature stamp in New Mexico?
No. 16.39.3.12(A) NMAC states that “Rubber stamps signatures are not acceptable.” The seal itself may be rubber; the signature beside it may not. Engineers who order a combined signature-and-seal die are buying something the rule forbids.
Where do the signature and date go?
Adjacent to the seal. The rule: “Adjacent to the seal/stamp shall appear the original signature of the licensee along with the date the signature was applied.” The date is the date the signature was applied, not the date of the seal or of the drawing, and nothing requires the signature to cross the seal.
Which New Mexico documents have to be sealed, and does every sheet need it?
Final engineering design drawings, the certification page of specifications, and engineering reports prepared by the licensee in responsible charge, under subsection A. Subsection G governs sets: the first or title page carries the responsible licensee’s seal and signature, each sheet is sealed and signed by the licensee or licensees responsible for it, and where several licensees sign, each person’s portion of the work must be identified. Subsection E permits a licensee in responsible charge to sign, seal and date documents the licensee did not personally prepare, where another licensed engineer sealed them and the licensee or supervised persons reviewed and tested the work. Subsection F limits seal and signature to work in the licensee’s responsible charge and within the licensee’s discipline.
Does a New Mexico engineering firm need a license or a certificate of authorization?
No. New Mexico licenses no business entities. NMSA 1978 § 61-23-21(A) states that “No business entity shall be licensed pursuant to the Engineering and Surveying Practice Act.” The entity files an affidavit instead: 16.39.3.11(E) NMAC requires an authorized company officer and the professional engineer employed by the entity and in responsible charge to place a signed affidavit on file with the board within 30 days, kept current and revised within 30 days of any change. Nothing requires a firm number, affidavit number or certificate of authorization number on a sealed document.
Does New Mexico allow electronic signatures?
Yes, as an option, with the security burden on the licensee: “An electronic signature, as an option to a permanently legible signature, is acceptable for professional documents. The licensee shall provide adequate security regarding the use of the seal and signature. If the document contains more than one licensee and is electronically transmitted as specified under the preceding paragraph, each signature must contain an independent electronic signature.” No certificate authority, cryptographic standard or file format is named. Subsection A conditions acceptance on “law and board’s policy,” so a board policy statement can change practice without a rule amendment.
I was licensed years ago. Is my old New Mexico seal still valid?
Probably, if your licensure has been continuous. Subsection D of 16.39.3.12 NMAC grandfathers older devices: engineers licensed before the current rules who have maintained continuous licensure may keep a previously approved seal. The clause is one-way, which implies that a break in licensure ends the protection.
What happens to my seal if my New Mexico license lapses?
Not addressed. Neither 16.39.3 NMAC nor the Engineering and Surveying Practice Act says what becomes of the seal on expiration, lapse, retired or inactive status, or revocation, and neither says whether the license number changes on reinstatement. Checked 16.39.3.11 and 16.39.3.12 NMAC and the 2025 Practice Act. The only related provision is the grandfather clause at subsection D, which is conditioned on continuous licensure.































